Browsing by Author "Auras, Rafael"

Now showing 1 - 2 of 2

Citation - WoS: 9
Citation - Scopus: 13
Carbon Nanotube Release From Polymers Into a Food Simulant
(Elsevier Sci Ltd, 2017) Xia, Yining; Unalan, Ilke Uysal; Rubino, Maria; Auras, Rafael
The release assessment of multi-walled carbon nanotubes (CNTs) was performed on two types of polymer-CNT nanocomposites: polypropylene (PP) and polyamide 6 (PA6) containing 3 wt% CNT. Nanocomposite films were prepared and then exposed to ethanol as a fatty-food simulant at 40 degrees C, and the amount of CNT release into ethanol was determined by ultraviolet-visible spectroscopy (UV-Vis) and graphite furnace atomic absorption spectrometry (GFAAS). The CNTs released into ethanol were visualized by transmission electron microscopy (TEM) and verified by Raman spectroscopy. UV-Vis analysis showed a very small amount of CNT release from the nanocomposite films into ethanol over 60 d: maximum CNT concentrations in ethanol were 1.3 mg/L for the PP-CNT film and 1.2 mg/L for the PA6-CNT film. GFAAS results indicated that the amount of CNTs released into ethanol after 12 d was over 20-fold higher than the results obtained by UV-Vis. Overestimation of CNT release by GFAAS suggested aggregation and poor dispersion of CNTs in the solvent. This assumption was verified by TEM images exhibiting the embedded CNTs in the polymer flakes, which could be poorly dispersed in the solvent. In general, CNT release from the nanocomposite films was considered a surface phenomenon, as indicated by detachment of CNT-containing polymer flakes from the film surface. (C) 2017 Elsevier Ltd. All rights reserved.
Citation - WoS: 38
Citation - Scopus: 52
Toughening of Poly(lactic Acid) and Thermoplastic Cassava Starch Reactive Blends Using Graphene Nanoplatelets
(Mdpi, 2018) Bher, Anibal; Unalan, Ilke Uysal; Auras, Rafael; Rubino, Maria; Schvezov, Carlos E.
Poly(lactic acid) (PLA) was reactively blended with thermoplastic cassava starch (TPCS) and functionalized with commercial graphene (GRH) nanoplatelets in a twin-screw extruder, and films were produced by cast-film extrusion. Reactive compatibilization between PLA and TPCS phases was reached by introducing maleic anhydride and a peroxide radical during the reactive blending extrusion process. Films with improved elongation at break and toughness for neat PLA and PLA-g-TPCS reactive blends were obtained by an addition of GRH nanoplatelets. Toughness of the PLA-g-TPCS-GRH was improved by similar to 900% and similar to 500% when compared to neat PLA and PLA-g-TPCS, respectively. Crack bridging was established as the primary mechanism responsible for the improvement in the mechanical properties of PLA and PLA-g-TPCS in the presence of the nanofiller due to the high aspect ratio of GRH. Scanning electron microscopy images showed a non-uniform distribution of GRH nanoplatelets in the matrix. Transmittance of the reactive blend films decreased due to the TPCS phase. Values obtained for the reactive blends showed similar to 20% transmittance. PLA-GRH and PLA-g-TPCS-GRH showed a reduction of the oxygen permeability coefficient with respect to PLA of around 35% and 50%, respectively. Thermal properties, molecular structure, surface roughness, XRD pattern, electrical resistivity, and color of the films were also evaluated. Biobased and compostable reactive blend films of PLA-g-TPCS compounded with GRH nanoplatelets could be suitable for food packaging and agricultural applications.